EC15 pixel led - Ultra-small SK6812 LED with 1.5x1.5mm size

1, EC15 is one ultra-small SK6812 pixel led chip with 1.5x1.5mm size, it is an embedded control type LED light source integrating control circuit and light-emitting circuit. It contains intelligent digital interface data latch signal shaping and amplifying drive circuit, power supply voltage regulator circuit, built-in constant current circuit and high precision RC oscillator. The output driver adopts the patented PWM technology, which effectively ensures the high color consistency of the light in the pixel.
  The data protocol being used is unipolar RZ communication mode. The 24-bit data is transmitted from the controller to DIN of the first element, and if it is accepted it is extracted pixel to pixel. After an internal data latch, the remaining data is passed through the internal amplification circuit and sent out on the DO port to the remaining pixels. The pixel is reset after the end of DIN. Using automatic shaping forwarding technology makes the number of cascaded pixels without signal transmission only limited by signal transmission speed.
  The LED has a low driving voltage (which allows for environmental protection and energy saving), high brightness, scattering angle, good consistency, low power, and long life. The control circuit is integrated into the LED above.

2. Main Features :
● Easy to design
● Easy to build
● Easy to program

3. Description:
● EC LED internal integrated high-quality external control line serial cascade constant current IC;
●built-in data shaping circuit, a pixel signal is received after wave shaping and output waveform distortion will not guarantee a line;
●The built-in power-on reset and reset circuit, the power does not work;
●gray level adjusting circuit (256 level grayscale adjustable);
● red drive special treatment, color balance;
● line data transmission;
● plastic forward strengthening technology, the transmission distance between two points over 10M;
●Using a typical data transmission frequency of 800 Kbps, when the refresh rate of 30 frames per sec

4. Mechanical Dimensions:
5. PIN configuration
1. All dimensions are in millimeters.
2. Tolerance is ±0.1mm unless otherwise noted
5. Product welding plate size
7. General Information
8. Absolute Maximum Ratings (Ta=25℃,VSS=0V)
9. Electrical/Optical Characteristics:

10. The electrical parameters (unless otherwise specified, TA=-20 ~ +70 ℃, VDD=4.5 ~ 5.5V, VSS=0V):
11. The dynamic parameters (Ta=25 ℃):

12. The data transmission time :
1. The protocol uses a unipolar zeroing code. Each symbol must have a low level. Each
symbol in this protocol starts with a high level. The high time width determines the "0" or
"1" code. .
2. When writing programs, the minimum symbol period is 1.2μs.
3. The high time of “0” code and “1” code should be in accordance with the
stipulated range in the above table. The low time requirement of “0” code and “1”code is less than 1.2μs.

13. Timing wavefrom:
        Input code:
         Connection mode:
14. The method of data transmission:
Note: the D1 sends data for MCU, D2, D3, D4 for data forwarding automatic shaping cascade circuit.

15. The data structure of 24bit:
    Note: high starting, in order to send data (G7 - G6 - ...... ..B0)

16. The typical application circuit:
Product signal input and output must be connected in series Protection resistor R1, R1 depends on the size of the cascade lamp beads, the greater the number of cascade, the smaller R1, the general recommended value between 200-2KΩ, usually recommended Worth about 500 euros;

16. Standard LED Performance Graph:
More details, please contact us.


WS2815 compare GS8208, 12V pixel LED SMD

  Now 12V pixel LED is more popular, can be more widely used than 5v pixel led. nowadays there are two mature products, one is WS2815 DC12V pixel LED, another one is GS8208 12v pixel LED, actually WS2815 12v led came out earlier than GS8208, and has been updated several times, now ws2815 is more stable and mature than before. About the GS8208, it is a clone led of WS2815, but with more interesting features. just like the SK9822, one clone led of APA102/APA107.

so what is the different of WS2815 and GS8208? 

Firstly, let us see the WS2815.
WS2815 is an intelligent control LED light source that the control circuit and RGB chip are integrated in a package of 5050 components. Its internal includes intelligent digital port data latch and signal reshaping amplification drive circuit.
Dual-signal wires version, signal break-point continuous transmission. Any pixel’s failure won't affect signal transfer and total emitting effect. The data transfer protocol uses a single NZR communication mode. After the pixel power-on reset, the DIN port receives data from the controller, the first pixel collects initial 24bit data then sent to the internal data latch, the other data which
reshaping by the internal signal reshaping amplification circuit sent to the next cascade pixel through the DO port. After transmission for each pixel, the signal to reduce 24bit. Every pixel adopts auto-reshaping transmit technology, making the pixel cascade numbers are not limited to the signal transmission, only relate to the speed of signal transmission.
The BIN receives the data signal, and then compare the data with the DIN side after phagocytosis of 24bit data, if DIN do NOT receive the signal, then switching to BIN for receiving the input signal, which ensures that any the IC's damage does not affect the signal cascade transmission and make the BIN in state of receiving signal until restart after power-off.
Refresh Frequency updates to 2KHz, Low Frame Frequency, and no Flicker appear in HD Video Camera.
RESET time>280μs, it won’t cause the wrong reset while interruption, it supports the lower frequency and inexpensive MCU.
Integrated circuit chips enable the circuit control simpler, neater and more reliable while NO extra components needed.

Mechanical Dimensions
PIN Configuration
PIN Function
Absolute Maximum Ratings
Electrical Characteristics (TA=-20~+70℃, VDD=4.5~5.5V, VSS=0V)
Switching Characteristics (TA=-20~+70℃, VDD=4.5~5.5V, VSS=0V)
LED Characteristics
Data Transfer Time
Data Transmission Method
                                                 Note: D1 is the data from MCU, and D2, D3, D4 are from Cascade Circuits
The composition of 24bit data
                                                 Note: Data transmit in order of GRB, high bit data is first.
Typical application circuit
1. Recommended application circuit
Remarks: C1 is bypass filter capacitor, its value of 100NF.

2. For complicated wiring & space-saving

So what is GS8208? 
  The GS8208 is a 3-channel constant current LED driver with resumable data transfers and internal display patterns. There are three open-drain constant current outputs, with a built-in PWM of grayscale. The range of input power is from 9VDC to 15VDC, and voltage-endurance of LED port is +12VDC. there is a built-in 12bits GAMMA correction module. PWM maximum refresh frequency is 8kHz. The GS8208 use the e-Rz (extended return to zero code) as the signal transmission mode, which can control the output current channel by channel and cascade infinitely. GS8208 provides two signal data input as redundant control, which ensures the transmission of the signal if any single chip damages. In the absence of signal input, GS8208 displays the built-in display patterns that are suitable for those applications without a controller. there is the built-in power-on the power-off protection in the driver, which can enhance the service life of the chip. It also has the automatic test function while power on, which is convenient for the customer to test. The GS8208 provides SOP8 packaging, the working environment is from -° 40° C to + 85C.

-12V operating supply voltage with 7805 module inside
-Default 17.5mA constant current output, the minimum is 11mA.
-Use e-Rz code, serial data frequency 800kHz.
-8bits data transfer, 12bits build-in GAMMA correction of PWM display.
-Built-in PWM technology, supports 8kHz PWM refresh rate.
-With resumable data transfer function, single chip damage does not infect data transmission.
-Built-in automatic test mode, power-on and power-off protection.
-ESD: 2KV.

Typical Applications:

Block Diagram
PIN Description
Equivalent Circuits of Input and Output
Maximum Ratings
(1) Stresses above there ratings may cause permanent damage. Exposure to absolute maximum condition for extended periods may degrade device reliability. These are stress ratings only and functional operation of the device at these or any other condition beyond those specified is not supported.
(2) All voltage values are with respect to the ground terminal.

Electrical Characteristics
Switching Characteristics
Typical Application
Data Format
  GS8208 adopts the extended return zero code (e-RZ) data transmission mode, 8bits data for a single channel, each IC support 3 channel for display. The transmission data is filtered internally to support the data anti-jitter function. The extension type is compatible with traditional RZ code. So it is suitable for most of RZ code controller in the market.
Single code with 1:3 duty cycle and a standard 800kHz transmission speed. The maximum frequency can reach 1MHz. GS8208 re-code the data before transmission. Data delay is less than 0.7us from chip to chip, meets the dynamic image needs.
Dual Channel redundant control
   Dual channel redundant control can be used to effectively avoid the failure of any single device damage, and reduce the damage rate of driving system to one millionth. The SDI signal is used as the default transmission channel while the system is power on. The transmission channel priority is switched between SDI and SDI2 when the transmission data is abnormal. The device will choose the clear transmission channel after data detection.
When the external control data is transmitted, SDI used the 1-24bits received data as the display data, meanwhile SDI2 will discard the 1-24bits data and use 25-48bits data as the display data.

Dual Channel status testing during production
  In the production process, any one of the abnormal data channel will not affect display because the chip uses dual SDI input. it is difficult to detect the problem data channel during the production process, which may cause the dual channel is equivalent to a single channel.
  In order to avoid this situation, the status of the data channel can be detected by using the test controller in the external control situation. While any channel appears weld, short, open or other abnormal communication, the chip will display in white to facilitate the detection of the problem position.

Working principle of series structure LED controller
  it is RGB LED series structure. Power supply voltage is 12V, and the LED constant current is 18mA. Different to the parallel architecture of 5v power supply and 54mA driver current, the series architecture can provide a better driver ability. The new architecture's total driver current is only 1/3 of the original one and Vds=4V. The power loading ability is better.
  In the series structure mode, when the internal MOS paralleling with the LED is open, the current flow into the LED and the LED lights. When the internal MOS paralleling with the LED is short, the current flow into the MOS device and the LED close. Switching the MOS device by PWM signal can lights on or off the LED.
Working principle of series structure LED controller
  In order to prevent the large power interference from the LED switching, reduce the power circuit voltage fluctuations, GS8208 has built-in output hysteresis function. OUT1, OUT2, OUT3 will work in accordance with 80ns interval sequence, to improve the system's anti-jamming performance. Meanwhile, the current peak output stagger will reduce the system EMI radiation, to meet environmental requirements.
MPWM (multi-PWM)
  In order to increase the refresh rate of PWM output, MPWM adopts a unique method of dispersibility to distribute the periodic N in the display time, as shown in the figure below. GS8208 adopts MPWM technology, and the PWM refresh rate increases to 8kHz, which shows the gentle effect and does not affect the accuracy of output current.
MPWM (multi-PWM)
  GS8208 gets into RGB test mode right after power on. If the device does not receive the external display data for a long time, the chip will go into the built-in display patterns mode. The pattern on a total of six categories of 32 series, including integral color jump, integral color gradient, meteors, waves, colorful gradient, color jump of water circulation. It is 10 minutes about, and the image refresh frequency is 100hz.
  Under the internal display mode, the first chip's SDI/SDI2 needs to be connected to GND.
Power dissipation
  When all the three output channels are turned on, the practical power dissipation is determined by the following equation:
(Vout represents the output terminal voltage when the current is turned on; Duty represents the ratio of the time at which the current is turned on)
                    PD(practical) VccxIccVoutA2xIoutA2xDutyA2...VoutD0xIoutD0xDutyD0
In secure operation conditions, the power consumption of an integrated chip should be less than the maximum permissible power dissipation which is determined by the package types and ambient temperature. The formula for maximum power dissipation is described as follows: 
The PD (max) declines as the ambient temperature rises. Therefore, suitable operating conditions should be designed with caution according to the chosen package and the ambient temperature. The following figure illustrates the relation between the maximum power dissipation and the ambient temperature of the SOP8 package.
If you don't know which one is more suitable to you, please contact us.